| No. | mark | name | description |
|---|---|---|---|
| 300 |  |
FPGA error | Occurs if FPGA is not functioning properly. |
| 301 |  |
Main unit CPU internal RAM error |
Displayed when a malfunction occurs in the CPU's internal RAM, in the main unit. |
| 302 |  |
Main unit CPU internal FROM error |
Occurs when the checksum value in the CPU's internal FROM does not match the calculated checksum value, in the main unit. |
| 303 |  |
Main unit floating decimal division by zero error |
Displayed when division by zero occurs during floating point calculations in the main unit or if an invalid calculation occurs. |
| 304 |  |
Main unit external RAM error |
Displayed when a malfunction occurs in the main unit external RAM. |
| 305 |  |
Main unit external FROM error |
Displayed when a checksum value in the main unit external FROM does not match the calculated checksum value. |
| 306 |  |
Outrigger specifications not specified in EEPROM |
Occurs when replacing circuit boards. |
| 307 |  |
Outrigger specifications for DIP switches on circuit board does not agree with outrigger specifications in EEPROM | Occurs when replacing circuit boards. |
| 308 |  |
Outrigger specifications not specified on circuit board | Occurs when replacing circuit boards. |
| 409 |  |
EEPROM malfunction | Displayed when read/write from/to EEPROM fails. |
| 310 |  |
Main and display units communication error |
Main unit and display unit cannot communicate. |
| 313 |  |
Software code mismatch | Software codes for the main and display units do not match. |
| 314 |  |
The crane model and software code in the EEPROM do not match the crane model and software code in the program. | |
| 420 |  |
ACS-COR communication error | |
| 421 |  |
CORDT-FT communication error | |
| 422 |  |
Broken or short circuit in right-front outrigger stroke |
|
| 423 |  |
Broken or short circuit in right-rear outrigger stroke |
|
| 424 |  |
Broken or short circuit in left-rear outrigger stroke |
|
| 425 |  |
Broken or short circuit in left-front outrigger stroke |
|
| 426 |  |
Engine RPM sensor error | |
| 429 |  |
Outrigger adjustment error | Occurs when an outrigger fully retracted value is same as fully extended value or fully extended value is smaller, etc. |
| 333 |  |
Main unit CPU address error | Displayed when an address error occurs in the main unit CPU. If this occurs, the crane automatically stops, then the CPU stops functioning. |
| 334 |  |
Main unit CPU undefined error code 1 |
An undefined code 1 was executed in the main unit CPU. If this occurs, the crane automatically stops, then the CPU stops functioning. |
| 335 |  |
Main unit CPU undefined error code 2 | An undefined code 2 was executed in the main unit CPU. If this occurs, the crane automatically stops, then the CPU stops functioning. |
| 340 |  |
Broken or short circuit in boom length sensor |
|
| 440 |  |
Boom full retraction length error |
Displayed when there is a large amount of length error when the boom is fully retracted. Full retraction length can be manually adjusted. If this adjustment has been made, contact your authorized KATO dealer. |
| 441 |  |
Boom length offset adjustment value error |
[boom length offset adjustment value < -(47m -(max length - min length)] For KA-1300RX, this error occurs if adjustment value is less than -6.8m. |
| 443 |  |
Boom length adjustment value error |
[Boom length zero adjustment value < -(47m -(max length - min length)] For KA-1300RX, this error occurs if adjustment value is less than -6.8m. |
| 447 |  |
Jib connector error | Displayed when the boom status is set to boom or rooster sheave operation and the jib angle sensor connector is connected, indicating a faulty connector, or when the boom status is set to jib or boom with the jib operation and the jib connector is not connected. |
| 350 |  |
Broken or short circuit in boom angle |
|
| 351 |  |
Broken or short circuit in top angle sensor |
|
| 451 |  |
Broken or short circuit in top angle sensor |
|
| 452 |  |
Top angle error | If the difference between the top angle and boom angle is more than 10 degrees, check each sensor. |
| 355 |  |
Broken or short circuit in the jib angle detector |
|
| 357 |  |
Broken or short circuit in the jib length detector |
|
| 458 |  |
Jib length offset adjustment value error |
[Jib length offset adjustment value < 22.5m -(max length - min length)] For KA-1300RX, this error occurs if adjustment value is less than -5.1 m. |
| 360 |  |
Derrick sensor error | Derrick pressure sensor P1 or P2 malfunctioned. |
| 361 |  |
Broken or short circuit in derrick pressure sensor P1 | |
| 362 |  |
SL jib derrick pressure sensor error |
The SL jib derrick pressure sensor P1 or P2 is faulty. |
| 363 |  |
Broken or short circuit in SL jib derrick pressure sensor P1 |
|
| 364 |  |
Main winch rotation sticking error where it rotates in the lowering direction even though the main winch lever is operated in the hoisting direction | |
| 365 |  |
Main winch rotation sticking error where it rotates in the hoisting direction even though the main winch lever is operated in the lowering direction | |
| 366 |  |
Main winch rotation sticking error where it rotates in the hoisting direction even though the main winch lever is in the neutral position | |
| 367 |  |
Auxiliary winch rotation sticking error where it rotates in the lowering direction even though the auxiliary winch lever is operated in the hoisting direction | |
| 368 |  |
Auxiliary winch rotation sticking error where it rotates in the hoisting direction even though the auxiliary winch lever is operated in the lowering direction | |
| 369 |  |
Auxiliary winch rotation sticking error where it rotates in the hoisting direction even though the auxiliary winch lever is in the neutral position | |
| 371 |  |
Broken or short circuit in derrick pressure sensor P2 | |
| 372 |  |
Broken or short circuit in SL jib derrick pressure sensor P2 |
|
| 373 |  |
Main winch rotation sticking error where it rotates in the lowering direction even though the main winch lever is in the neutral position | |
| 374 |  |
Auxiliary winch rotation sticking error where it rotates in the lowering direction even though the auxiliary winch lever is in the neutral position |
|
| 376 |  |
Boom extension/retraction control lever sticking error |
Displayed when the boom length changes even though the boom extension/retraction control lever is not being operated or the boom length changes in the opposition direction of the control lever operation. |
| 377 |  |
Jib derricking/lowering control lever sticking error |
Displayed when the jib derricking/lowering position changes even though the jib derricking/lowering control lever is not being operated or it changes in the opposition direction of the control lever operation. |
| 378 |  |
Jib extension/retraction control lever sticking error |
Displayed when the jib length changes even though the jib extension/retraction control lever is not being operated or the jib length changes in the opposition direction of the control lever operation. |
| 380 |  |
Broken circuit in slewing angle sensor |
|
| 381 |  |
Broken circuit in slewing encoder signal A |
|
| 382 |  |
Broken circuit in slewing encoder signal B |
|
| 387 |  |
Slewing rear switch error | |
| 388 |  |
Slewing zero adjustment switch error |
|
| 390 |  |
Open top terminal communication circuit |
|
| 490 |  |
Open top terminal communication circuit |
|
| 391 |  |
Communication error with top terminal |
|
| 491 |  |
Communication error with top terminal |
|
| 495 |  |
Crane serial No. not specified in EEPROM | |
| 496 |  |
Main unit time reading error | Cannot read the main unit time. |
| 497 |  |
Battery voltage is 20V or less | |
| 498 |  |
Backup power supply wiring error |
Backup power supply voltage is 5V or less, due to broken or short circuit. Check the battery voltage and wiring. |
| 499 |  |
Overload data memory area is full | No or minimal memory space is available, because more than the specified number of overload data values were recorded. |
| 201 |  |
Moment stop | Displayed when the operation stops automatically after comparing current and limit loads during operations such as lowering or extending the boom, winding up the winch, or lowering the jib. |
| 203 |  |
Boom upper limit angle stop |
Displayed when a boom derricking stop angle is specified and the operation stops automatically after the boom angle reaches that angle. |
| 204 |  |
Boom upper limit angle stop warning |
Displayed when a boom derricking stop angle is specified and the intermittent
sound alarm "DING DONG, DING DONG" is output after the boom angle is -2 degrees or less from that stop angle. |
| 205 |  |
Boom lower limit angle stop |
Displayed when a boom lowering stop angle is specified and the operation stops automatically after the boom angle reaches that angle. |
| 206 |  |
Boom lower limit angle stop warning |
Displayed when a boom lowering stop angle is specified and the intermittent sound alarm "DING DONG, DING DONG" is output after the boom angle is +2 degrees or less from that stop angle. |
| 207 |  |
Right slewing stop | Displayed when slewing right and the operation stops after becoming dangerous. |
| 208 |  |
Right slewing stop warning |
Displayed when slewing right and a warning is output after reaching 5 degrees from the stop position. |
| 209 |  |
Left slewing stop | Displayed when slewing left and the operation stops after becoming dangerous. |
| 210 |  |
Left slewing stop warning | Displayed when slewing left and a warning is output after reaching 5 degrees from the stop position. |
| 211 |  |
Lower angle limit stop | Displayed when a lower angle limit is specified and the operation stops automatically after the boom angle reaches that limit value. |
| 212 |  |
Lower angle limit stop warning |
Displayed when a lower angle limit is specified and the intermittent sound alarm "DING DONG", "DING DONG" is output after the boom angle reaches +2 degrees or less from that limit value. |
| 213 |  |
Upper angle limit stop | Displayed when an upper angle limit is specified and the operation stops automatically after the boom angle reaches that limit value. |
| 214 |  |
Upper angle limit stop warning |
Displayed when an upper angle limit is specified and the intermittent sound alarm "DING DONG", "DING DONG" is output after the boom angle reaches -2 degrees or less from that limit value. |
| 215 |  |
Radius limit stop | Displayed when a radius limit is specified and the operation stops automatically after reaching that radius limit. |
| 216 |  |
Radius limit stop warning |
Displayed when a radius limit is specified and the intermittent sound alarm "DING DONG", "DING DONG" is output after the radius reaches -50cm or less from that limit value. |
| 217 |  |
Maximum hoist height limit stop |
Displayed when a maximum hoist height limit is specified and the operation stops automatically after reaching that height limit. |
| 218 |  |
Maximum hoist height limit stop warning |
Displayed when a maximum hoist height limit is specified and the intermittent sound alarm "DING DONG", "DING DONG" is output after reaching -50 cm from that hoist height limit. |
| 219 |  |
Right slewing limit stop | Displayed when a right slewing limit value is specified and right slewing stops automatically after the slewing angle reaches that limit value. |
| 220 |  |
Right slewing limit stop warning |
Displayed when a right slewing limit value is specified and the intermittent sound alarm "DING DONG, DING DONG" is output after the slewing angle reaches - 5 degrees or less from that limit value. |
| 221 |  |
Left slewing limit stop | Displayed when a left slewing limit value is specified and left slewing stops automatically after the slewing angle reaches that limit value. |
| 222 |  |
Left slewing limit stop warning |
Displayed when a left slewing limit value is specified and the intermittent sound alarm "DING DONG, DING DONG" is output after the slewing angle reaches - 5 degrees or less from that limit value. |
| 223 |  |
Auto-stop of all operations | Displayed when all operations stop automatically. |
| 225 |  |
Error auto-stop | Displayed when an operation stops automatically after an error occurs. Auto-stop does not occur for Fxx errors. |
| 226 |  |
Error warning | Displayed when the intermittent sound alarm "DING DONG DING DONG" is output after an error occurs. |
| 228 |  |
Lever stand stowage warning |
Displayed when a control lever is operated with the lever stand stowed. "DING DONG. Set the lever stand." is emitted. |
| 229 |  |
Line pull stop | Displayed when an operation stops automatically after the line pull force (actual load/number of parts of line) exceeds the allowable line pull force. |
| 230 |  |
Line pull stop warning | Displayed when the intermittent sound alarm "DING DONG", "DING DONG" is output after the line pull force (actual load/number of parts of line) exceeds the allowable line pull force. |
| 231 |  |
Maximum boom angle stop |
Displayed when an operation stops automatically after the boom reaches the specified maximum angle. |
| 232 |  |
Maximum jib angle stop | Displayed when the jib angle reaches the maximum jib angle setting and the jib stops automatically. |
| 233 |  |
Stopped due to disconnected connector for confirming jib connection | Displayed when a jib control lever is operated and the operation is automatically stopped because the connector for the jib angle detector is not connected to the top terminal. |
| 234 |  |
Special maximum jib angle stop |
Displayed when the jib angle reaches the special maximum jib angle setting and the jib stops automatically. The maximum angle changes to the range of 2 to 5 degrees when the SL jib length is in the range of 9.2 to 15.0 meters. The jib cannot be raised or retracted. |
| 235 |  |
Jib fully-lowered stop | Displayed when the jib angle reaches the preset fully-lowered angle and the jib stops automatically. |
| 236 |  |
Jib fully-lowered stop warning |
Displayed when the intermittent sound alarm "DING DONG", "DING DONG" is output after the jib reaches +2 degrees or less from the preset fully-lowered angle. |
| 239 |  |
Derrick lowered end stop | Displayed when the boom has been lowered to the cylinder end and an operation to lower the boom, extend the boom, or wind up the winch is automatically stopped. |
| 243 |  |
Target 1 partially within range |
Displayed when either the slewing angle or radius of the target 1 is within the specified range (±1.5 m radius or ±7.5 degrees slewing angle). |
| 244 |  |
Target 1 within range | Displayed when both the slewing angle and radius of the target 1 is within the specified range (±1.5 m radius and ±7.5 degrees slewing angle). |
| 245 |  |
Target 2 partially within range |
Displayed when either the slewing angle or radius of the target 2 is within the specified range (±1.5 m radius or ±7.5 degrees slewing angle). |
| 246 |  |
Target 2 within range | Displayed when both the slewing angle and radius of the target 2 is within the specified range (±1.5 m radius and ±7.5 degrees slewing angle). |
| 248 |  |
SL jib full retraction switch detected |
Displayed when the SL jib full retraction switch is detected. |
| 249 |  |
Slewing soft stop output | Displayed when a slewing soft stop is output. |
| 251 |  |
External memory device power is OFF |
Displayed when the power supply for an external memory device is attached to the ACS and the power for the external memory device is OFF. |
| 252 |  |
No memory card is inserted in external memory device |
Displayed when an external memory device is attached to the ACS and a memory card is not inserted in the external memory device. |
| 253 |  |
Auto-stop for sticking winch control lever |
Displayed when the operation stops automatically due to the winch rotating when the winch is not being operated and the winch valve spool is presumed to be stuck. The PTO or power supply must be shut OFF to cancel this icon. |
| 254 |  |
Auto all-stop of boom lowering lever |
Displayed when all other operations stop automatically due to the boom derricking/lowering lever being in the lowering position. |
| 255 |  |
Auto all-stop of boom derricking lever |
Displayed when all other operations stop automatically due to the boom derricking/lowering lever being in the derricking position. |
| 256 |  |
Auto all-stop of boom extension lever |
Displayed when all other operations stop automatically due to the boom extension/retraction lever or pedal being in the extension position. |
| 257 |  |
Auto all-stop of boom retraction lever |
Displayed when all other operations stop automatically due to the boom extension/retraction lever or pedal being in the retraction position. |
| 258 |  |
Auto all-stop of main winch hoisting lever |
Displayed when all other operations stop automatically due to the main winch lever or pedal being in the hoisting position. |
| 259 |  |
Auto all-stop of main winch lowering lever |
Displayed when all other operations stop automatically due to the main winch lever or pedal being in the lowering position. |
| 260 |  |
Auto all-stop of auxiliary winch hoisting lever |
Displayed when all other operations stop automatically due to the auxiliary winch lever or pedal being in the hoisting position. |
| 261 |  |
Auto all-stop of auxiliary winch lowering lever |
Displayed when all other operations stop automatically due to the auxiliary winch lever or pedal being in the lowering position. |
| 262 |  |
Auto all-stop due to jib derricking/retraction lever |
Displayed when all other operations stop automatically due to the SL jib derricking/lowering lever being in the derricking position or the SL jib extension/retraction lever being in the retraction position. |
| 263 |  |
Auto all-stop due to jib lowering/extension lever |
Displayed when all other operations stop automatically due to the SL jib derricking/lowering lever being in the lowering position or the SL jib extension/retraction lever being in the extension position. |
| 264 |  |
Auto all-stop of slewing lever to rightward |
Displayed when all other operations stop automatically due to the slewing lever being in the right side. |
| 265 |  |
Auto all-stop of slewing lever to leftward |
Displayed when all other operations stop automatically due to the slewing lever being in the left side. |
| 269 |  |
External memory device error |
Displayed when an external memory device is attached to the ACS and an error occurs in that memory device. |
| 270 |  |
Slewing brake output display |
Displayed when a slewing brake is output. |
| 271 |  |
Working area limit stop | Displayed when an auto-stop occurs due to a working area limit. |
| 272 |  |
Working area limit stop warning |
Displayed when the slewing angle is within 5 degrees from the working area limit stop angle or the working radius is within 50 cm from the working area limit stop radius. The intermittent sound alarm "DING DONG", "DING DONG" is output. |
| 278 |  |
Auto-stop by ACS emergency switch operation |
Displayed when the load rate has exceeded 100% in ACS emergency switch operation and the auto-stop function is activated. |
| 279 |  |
Auto-stop | |
| 283 |  |
Counterweight change warning | This warning is displayed for a few seconds when a change in counterweight detection has occurred. When the warning goes off, the counterweight will change. |
| 284 |  |
||
| 285 |  |
Main hook lifting height range |
Displayed when the main hook lifting height has approached the lifting height target, maximum lifting height or ground level. |
| 286 |  |
Main hook lifting height adjustment warning |
Displayed when it is determined that the main hook lifting height needs adjustment. |
| 287 |  |
Main hook rope limit warning |
Displayed when the rope cannot be payed out from the main drum any more. |
| 288 |  |
Auxiliary hook lifting height range |
Displayed when the auxiliary hook lifting height has approached the lifting height target, maximum lifting height or ground level. |
| 289 |  |
Auxiliary hook lifting height adjustment warning | Displayed when it is determined that the auxiliary hook lifting height needs adjustment. |
| 290 |  |
Auxiliary hook rope limit warning |
Displayed when the rope cannot be payed out from the auxiliary drum any more. |
| 291 |  |
2-telescopic cylinder-shutoff output display | When 2-telescopic cylinder-shutoff is being output. |
| 292 |  |
SL jib load stop | Auto-stop function that is activated when a load is hoisted with the SL jib hook with the boom status set to boom operation with the jib. Change the working status to SL jib operation. |
| 293 |  |
Fully retracted jib length adjusted |
Indicates that the automatic jib length adjustment function, on cranes with the function specified, has adjusted the jib length to the fully retracted length. |
| 294 |  |
Main load stop | Auto-stop function that is activated when a load is hoisted with the main hook with the boom status set to SL jib mode. Change the working status to boom operation with the jib. |
| 295 |  |
Adjusted boom to fully retracted length |
Indicates that the boom length was adjusted to its fully retracted length. It is displayed when the boom is retracted to its fully retracted length using only the boom retraction operation starting before the boom is fully retracted, the fully retracted length is confirmed, and the length is adjusted. |
| 296 |  |
Auto-stop by ACS emergency switch disabled |
Displayed when auto-stop by ACS emergency switch is not activated when the load rate has exceeded 100%. |
| 297 |  |
Crane record stopped | Displayed when the crane operation log is stopped. This also changes the movement indicator(* ) from flashing green and red to flashing blue and red. |
| 299 |  |
Overload event recorded | Displayed when an overload event is recorded. |
| 756 |  |
Boom extension control lever error |
Displayed when the boom extension lever switch is turned ON when the boom is retracting. (In the case of simultaneous input from the boom extension/retraction lever) |
| 757 |  |
Boom retraction control lever error |
Displayed when the boom retraction lever switch is turned ON when the boom is extending. (In the case of simultaneous input from the boom extension/retraction lever) |
| 758 |  |
Main winch hoisting control lever error |
Displayed when the main winch hoisting control lever switch is turned ON when the main winch is winding down. (In the case of simultaneous input from the main winch hoisting/lowering lever) |
| 759 |  |
Main winch lowering control lever error |
Displayed when the main winch lowering control lever switch is turned ON when the main winch is winding up. (In the case of simultaneous input from the main winch hoisting/lowering lever) |
| 760 |  |
Auxiliary winch hoisting control lever error |
Displayed when the auxiliary winch hoisting control lever switch is turned ON when the auxiliary winch is winding down. (In the case of simultaneous input from the auxiliary winch hoisting/lowering lever) |
| 761 |  |
Auxiliary winch lowering control lever error |
Displayed when the auxiliary winch lowering control lever switch is turned ON when the auxiliary winch is winding up. (In the case of simultaneous input from the auxiliary winch hoisting/lowering lever) |
| 762 |  |
Jib derricking control lever error |
Displayed when the jib derricking control lever switch is turned ON when the jib is lowering. (In the case of simultaneous input from the jib derricking/lowering lever) |
| 763 |  |
Jib lowering control lever error |
Displayed when the jib lowering control lever switch is turned ON when the jib is derricking. (In the case of simultaneous input from the jib derricking/lowering lever) |
| 764 |  |
Jib extension control lever error |
Displayed when the jib extension control lever switch is turned ON when the jib is retracting. (In the case of simultaneous input from the jib extension/retraction lever) |
| 765 |  |
Jib retraction control lever error |
Displayed when the jib retraction control lever switch is turned ON when the jib is extending. (In the case of simultaneous input from the jib extension/retraction lever) |
| 842 |  |
Range limit set/cancel error | Displayed when a working range limit setting is entered or canceled while a control lever is being operated. If this occurs, the range limit is not set or canceled. This icon will switch off after 3 seconds. |
| 237 |  |
Horizontal boom stop | Displayed when a horizontal boom stop is specified and the boom stops automatically after the boom angle reaches zero degrees. |
| 242 |  |
Hook stowage warning | Displayed when a warning is output because a crane for which the hook stowage control is specified gets to the hook stowage status. |
| 247 |  |
Boom soft stop output | Displayed when the boom soft stop switch is ON and a boom soft stop is output. |
| 248 |  |
Boom lowering contact stop | Displayed when the boom lowering stop angle is specified depending on the slewing angle and the operation stops after the boom angle reaches that limit angle. |
| 270 |  |
Auto-stop | |
| 273 |  |
Working area limit CD stop | Displayed when an auto-stop occurs due to working area limit CD. |
| 274 |  |
Working area limit CD warning | Displayed when the slewing angle is within 5 degrees from the working area limit CD stop angle or the working radius is within 50 cm from the working area limit CD stop radius. The intermittent sound alarm "DING DONG", "DING DONG" is output. |
| 276 |  |
Jib stowage pin warning | This warning is output when the main or rooster mode is selected without the jib foot pins being inserted properly. |
| 284 |  |
Jib upper angle proximity warning | Displayed during jib upper angle soft stop control. When the boom soft stop is OFF, this is displayed from 10 degrees before the jib upper angle. |
| 285 |  |
Jib fully raised and stops | Displayed when the jib is fully raised and stops |
| 286 |  |
Overhoisting stop cancel | Displayed when overhoisting stop does not occur, e.g. in case of jib setting. |
| 289 |  |
Load factor limit stop | Displayed when an auto-stop occurs due to load factor limit. |
| 290 |  |
Load factor limit stop warning | Displayed when the load factor is within 5% of the stop load factor due to load factor limit. The intermittent sound alarm "DING DONG", "DING DONG" is output. |
| 291 |  |
Auto-stop by ACS emergency switch operation | Displayed when the auto-stop by the ACS emergency switch operation is activated when the load rate has exceeded 100%. |
| 292 |  |
Release of auto-stop by ACS emergency switch operation | Displayed when the auto-stop by the ACS emergency switch operation is not activated when the load rate has exceeded 100%. |
| 294 |  |
Adjusted boom to fully extended length | Indicates that the boom has been fully extended to its maximum length. Displayed when, before the boom is fully extended, the boom is extended using only the boom extending operation and the boom length is adjusted when confirming the boom has stopped at the fully extended position. |
| 295 |  |
Adjusted boom to fully retracted length | Indicates that the boom has been fully retracted to its minimum length. Displayed when, before the boom is fully retracted, the boom is retracted using only the boom retracting operation and the boom length is adjusted when confirming the boom has stopped at the fully retracted position. |
| 749 |  |
Lowering motion limit stop | Displayed when a lever is operated when the lowering motion limit has been reached. |
| 750 |  |
Lowering motion limit alarm | Displayed when the lowering motion limit has been reached. |
| 767 |  |
Jib lowering stop | Displayed when an automatic stop occurs because the jib derricking/lowering lever is in the lowering position. |
| 769 |  |
Boom extension stop | Displayed when auto-stop occurs because the boom extension/retraction lever is in the extension position. |
| 771 |  |
Boom retraction stop | Displayed when auto-stop occurs because the boom extension/retraction lever is in the retraction position. |
| 773 |  |
Jib extension stop | Displayed when auto-stop occurs because the jib extension/retraction lever is in the extension position. |
| 774 |  |
Jib retraction stop | Displayed when auto-stop occurs because the jib extension/retraction lever is in the retraction position. |
| 778 |  |
Jib derricking stop | Displayed when auto-stop occurs because the jib derricking/lowering lever is in the derricking position. |
| 779 |  |
Main winding stop | Displayed when an auto-stop of the winding occurs because the main winch lever is in the winding position. |
| 793 |  |
Slow operating mode | Icon displayed during operations in the slow mode. (including the time of preoperational checks) |
| 866 |  |
Slow operating mode | Icon displayed during operations in the slow mode. (including the time of preoperational checks) |
| 866 |  |
Auto-stop of boom lowering during searcher hook operations | Displayed when an auto-stop occurs due to boom lowering lever operations performed during searcher hook operations. |
| 867 |  |
Auto-stop of boom raising during searcher hook operations | Displayed when an auto-stop occurs due to boom raising lever operations performed during searcher hook operations. |
| 868 |  |
Auto-stop of boom extension during searcher hook operations | Displayed when an auto-stop occurs due to boom extension lever operations performed during searcher hook operations. |
| 876 |  |
Emergency right-slew stop | Displayed if ACS emergency operations are disabled due to slewing to the right during ACS emergency operations. (See "ACS emergency operations".) |
| 877 |  |
Emergency left-slew stop | Displayed if ACS emergency operations are disabled due to slewing to the left during ACS emergency operations. (See "ACS emergency operations".) |
| 878 |  |
Auxiliary winch stop 2 | Displayed if the auxiliary winch is operated when operating the searcher hook or the boom with the searcher hook attached. It automatically stops the operation. |
| 879 |  |
Emergency crane operations | Displayed when the emergency operating device is used. |
| 880 |  |
Boom lowering contact warning | Displayed when the boom lowering stop angle is specified depending on the slewing angle and the boom angle reaches +2 degrees from that limit angle. |
| 881 |  |
Right slewing contact stop | Displayed when the right slewing stop angle is specified depending on the boom angle and the slewing angle reaches that limit angle. |
| 882 |  |
Right slewing contact warning | Displayed when the right slewing stop angle is specified depending on the boom angle and the slewing angle reaches -5 degrees from that limit angle. |
| 883 |  |
Left slewing contact stop | Displayed when the left slewing stop angle is specified depending on the boom angle and the slewing angle reaches that limit angle. |
| 884 |  |
Left slewing contact warning | Displayed when the left slewing stop angle is specified depending on the boom angle and the slewing angle reaches +5 degrees from that limit angle. |
| 885 |  |
Boom lowering warning during searcher hook operations | Displayed when an auto-stop occurs due to boom lowering lever operations performed during searcher hook operations and then the lever is returned to the neutral position. When the icon is displayed, the operation stops automatically when the specified lever is operated. |
| 886 |  |
Boom raising warning during searcher hook operations | Displayed when an auto-stop occurs due to boom raising lever operations performed during searcher hook operations and then the lever is returned to the neutral position. When the icon is displayed, the operation stops automatically when the specified lever is operated. |
| 887 |  |
Boom extension warning during searcher hook operations | Displayed when an auto-stop occurs due to boom extension lever operations performed during searcher hook operations and then the lever is returned to the neutral position. When the icon is displayed, the operation stops automatically when the specified lever is operated. |
| 1230 |  |
Outrigger retraction operation | Displayed when only outrigger retraction operation is selected. |
| 1231 |  |
Horizontal retraction operation | Displayed when a horizontal cylinder or retraction operation is selected. |
| 1232 |  |
Vertical retraction operation | Displayed when a vertical cylinder or retraction operation is selected. |
| 1233 |  |
Outrigger extension operation | Displayed when only outrigger extension operation is selected. |
| 1235 |  |
Vertical extension operation | splayed when a vertical cylinder or extension operation is selected. |
| 1236 |  |
Horizontal operation | Displayed when only horizontal cylinder operation is selected. |
| 1237 |  |
Vertical operation | Displayed when only vertical cylinder operation is selected. |
| 1243 |  |
Outrigger extension/retraction operation error |
Displayed when there is an abnormality in the signal for extension or retraction operation. |
| 1244 |  |
Horizontal/vertical operation error | Displayed when there is an abnormality in the signal for horizontal or vertical operation. |
| 442 |  |
Full retraction switch stuck error | |
| 484 |  |
Broken or short circuit in slewing potentiometer | |
| 485 |  |
Slewing potentiometer reference point failure | |
| 486 |  |
Slewing potentiometer voltage failure | |
| 489 |  |
Slewing encoder and potentiometer angles are inconsistent. | |
| 241 |  |
Hook stowage auto-stop | Displayed when auto-stop is output in the hook stowage status on a crane for which the hook stowage control is specified. |
| 267 |  |
Seat switch stop | Displayed when a lever operation is attempted without the operator sitting in the seat and the operation stops. |
| 277 |  |
Auto-stop for prevention to break the jib stowage bracket | Displayed when the boom length is below +0.5m from min. length, boom angle is more than 10 degrees, and jib stowage link switch is turned OFF with jib setting mode. Appeared when telescopic extension is operated. |
| 280 |  |
Jib drawing/release enabled status | Displayed when the boom length is below +0.2m from min. length, boom angle is within 55 to 65 degrees, and jib stowage link switch is turned ON with jib setting mode. |
| 281 |  |
Jib stowage link warning | Displayed when the boom length is below +0.2m from min. length, boom angle is within 10 to 35 degrees, and jib stowage link switch is turned ON with jib setting mode. |
| 768 |  |
Releasing Jib derricking pressure status | Displayed when the pilot pressure of jib derricking is released. |
| No. | mark | name | description |